Introduction
If you use a Lascal BuggyBoard with a stroller in the United States, you can usually remove the board without taking off the stroller connectors. Press the release buttons on both sides, then lift the BuggyBoard away from the connector arms. The exact button color and release shape may vary by model, such as the BuggyBoard Mini, Maxi, or Connect.
Remove the board on level ground. Keep one hand on the stroller and keep children away from the board while you release it. If the board does not lift free with light pressure, stop and check the model instructions instead of forcing the fittings.
What You Need Before Removing the BuggyBoard
You do not normally need tools to remove a Lascal BuggyBoard. Prepare a clear, flat space and make sure the stroller cannot roll.
Before you start:
- Park the stroller on level ground.
- Apply the stroller brake.
- Remove your child from the stroller if the stroller may move.
- Take bags or other items off the BuggyBoard.
- Stand behind or beside the stroller where you can hold it.
- Find the two BuggyBoard connector points on the stroller frame.
Lascal BuggyBoards attach to the stroller with connector fittings. The fittings stay on the stroller in most quick-release setups. The board itself comes away from these fittings when you press the release controls.
Identify the release parts
Look at both sides of the BuggyBoard. Each side connects to a fitting mounted on the stroller frame. You may see:
- A red release button
- A push tab or latch
- A connector housing around the board arm
- A small gap where the board arm enters the fitting
The release must be operated on both sides. Releasing only one side can twist the board and place extra force on the connector.
How to Remove a Lascal BuggyBoard
Follow these steps for most Lascal BuggyBoard Mini and Maxi models with quick-release connectors.
1. Secure the stroller
Set the stroller brake and hold the handle with one hand. Keep the stroller straight so the two connectors carry an even load.
Do not try to remove the board while the stroller is moving. Do not lift the stroller by the BuggyBoard.
2. Stand behind the board
Face the stroller from the rear. Place your feet so you can lift the board upward without stepping on it.
If the board is under tension, gently move it a small amount to take pressure off the connectors. Do not bend the arms from side to side.
3. Press both release buttons
Press the release button on the left connector and the release button on the right connector at the same time, if possible.
On many Lascal models, these buttons are red. On some versions, the release may look like a latch or push tab. Press the part marked or shaped as the release control. Do not press random parts of the connector housing.
4. Lift the board away
While holding both releases, lift the BuggyBoard upward and away from the stroller. Use a smooth motion.
If the board releases, set it on the ground. The connector fittings should remain attached to the stroller unless you intend to remove them as well.
5. Check the connectors
After removal, inspect both fittings. They should remain secure and should not show cracks, bent parts, or loose screws.
If one connector came off with the board, check whether it is still attached to the stroller frame. Refit it before using the BuggyBoard again.
6. Store the board safely
Store the BuggyBoard in a dry place. Avoid placing heavy items on the platform or hanging the board by one arm. Keep the release buttons free from sand, mud, and sticky dirt.
If the BuggyBoard Will Not Come Off
A board that will not release usually has a button that is not fully pressed, pressure on one connector, or dirt in the fitting. Use this order of checks.
Check whether both releases are pressed
The board may stay locked if one side remains engaged. Press both release controls firmly and evenly, then lift the board.
Do not use a screwdriver, pliers, or another sharp tool to pry the connector open. This can damage the lock and create a failure point.
Take pressure off the connectors
The board may bind when the stroller is angled or when one wheel sits higher than the other. Set the stroller straight and place all wheels on the same level surface.
You can gently move the board up and down by a small amount while pressing the releases. Do not jerk it or twist it.
Look for dirt or debris
Sand, dried mud, food, or small stones can block a release button. Brush away loose dirt with a soft, dry brush.
If the manufacturer’s instructions for your model permit cleaning, wipe the fitting with a slightly damp cloth and let it dry fully. Do not pour water into the connector. Avoid oil or grease unless Lascal specifically recommends it, because lubricant can attract grit or affect the latch.
Check for a locked or damaged part
Stop if you see:
- A cracked connector
- A bent attachment arm
- A release button that stays depressed
- A loose frame fitting
- A latch that does not return to its normal position
- A board that sits at an unusual angle
Do not use the BuggyBoard until the part is inspected or replaced. Contact Lascal or the retailer with the model name and a clear photo of the connector.
Removing the Stroller Connectors Completely
Removing the board is different from removing the stroller connectors. If you only need to store the board, leave the connectors on the stroller. This makes future attachment faster and reduces the chance of fitting them incorrectly.
If you need to remove the connectors, follow the instructions for your exact Lascal model. Connector designs can differ between BuggyBoard Mini, Maxi, and Connect versions, and stroller frame shapes also vary.
In general, complete connector removal may involve:
- Releasing the BuggyBoard from the fittings.
- Opening or loosening the connector straps or clamps.
- Sliding the fittings off the stroller frame.
- Reinstalling any frame protection pieces.
- Tightening the fittings only as directed by Lascal.
Do not cut the connector straps. Do not remove frame parts or stroller fasteners that are not part of the BuggyBoard attachment system.
After reinstalling the connectors, test the setup before placing a child on the stroller. The fittings should not slide, rotate, or pull away from the frame.
How to Confirm the Board Is Properly Removed and Reattached
A successful removal leaves the stroller stable and the connector parts undamaged. The board should separate without cracked plastic, bent arms, or forced parts.
Before using the BuggyBoard again:
- Check that both connector fittings are secure.
- Insert both board arms fully into the fittings.
- Confirm that both sides lock into place.
- Pull the board gently to check that it does not detach.
- Make sure the platform is level.
- Confirm that the board does not rub against the stroller wheels or brake.
- Test the stroller at walking speed without a child on the board.
The release buttons should work on both sides. If one side releases and the other does not, remove the board only when you can do so without twisting the attachment. Then inspect the uneven side.
Lascal’s product instructions take priority over general guidance because the release mechanism may vary by version. Use the model number printed on the product or packaging when looking for the correct manual.
Common Mistakes to Avoid
Pulling up on only one side
This can twist the board arm and load one connector. Press both releases before lifting.
Removing the board while the stroller is moving
A moving stroller can roll or tip when the board is detached. Always use the brake and work on level ground.
Forcing a stuck release
A stuck button may indicate dirt, misalignment, or damage. Prying can break the latch and make the board unsafe.
Assuming all BuggyBoards release the same way
Lascal has made several BuggyBoard designs. The Mini, Maxi, and Connect models may use different connector layouts. Confirm the model before following a diagram or video.
Leaving a loose connector on the stroller
A loose connector can catch on clothing, bags, or the stroller frame. Remove it or secure it according to the product instructions.
Using the board after damage
Do not use a board with a cracked platform, bent arm, damaged strap, or broken latch. A replacement part may be needed.
Quick Decision Guide
| Situation | Best next step |
|---|---|
| The board releases normally | Lift it away and leave the connectors in place |
| One side releases but the other stays locked | Realign the stroller and press both releases again |
| The button is blocked by dirt | Clean gently according to the model instructions |
| The board is bent or cracked | Stop using it and seek a replacement |
| A connector is loose | Do not carry a child on the board until it is secure |
| You want to remove the fittings too | Use the exact manual for your BuggyBoard model |
| You cannot identify the release | Check the model label and Lascal instructions |
The safest rule is simple: the board should come away with light, even pressure. If it needs force, something is wrong or the release method may be different.
Frequently Asked Questions
Can I remove a Lascal BuggyBoard without removing the connectors?
Usually, yes. The quick-release design on many Lascal BuggyBoard models allows the platform to come off while the stroller connectors remain attached to the frame.
Do I need to remove my child first?
Yes. Remove the child before releasing the board. Also remove bags or other weight from the platform.
Why is my Lascal BuggyBoard stuck?
Common causes include pressure from an angled stroller, a release button that is not fully pressed, dirt in the connector, or a damaged fitting. Align the stroller, press both releases, and inspect the parts without using force.
Can I use WD-40 or oil on the connector?
Do not apply oil or chemical lubricant unless Lascal’s instructions for your model recommend it. These products can attract dirt or affect plastic parts and the latch.
How do I know which Lascal BuggyBoard model I have?
Look for the model name or label on the board, connector, packaging, or original instructions. The board’s shape and platform size may also help, but the product label is more reliable.
What should I do if a connector breaks?
Stop using the BuggyBoard. Photograph the damaged part, record the model name, and contact Lascal or the seller for the correct replacement. Do not substitute an unapproved strap, clamp, or improvised fastener.
Conclusion
To remove a Lascal BuggyBoard, set the stroller brake, press both connector release controls, and lift the board away evenly. In most cases, the stroller fittings can stay attached.
If the board does not release with light pressure, check alignment and dirt first. Stop if you find damage or a loose connector, and use the exact Lascal instructions for your model before using the board again.
