If you need to remove the wheels from a Lascal BuggyBoard in the United States, first identify your model and check how the wheel is held in place. Most BuggyBoard Mini and Maxi versions use a removable wheel or wheel assembly secured by an axle, retaining clip, or release tab.
Do not force the wheel with a hammer or twist the board frame. If the wheel will not move with light hand pressure after the retainer is released, stop and check the model instructions. The mounting system can vary between older BuggyBoard models, newer BuggyBoard Maxi+ versions, and replacement wheel kits sold in the U.S.
Quick answer
To remove a Lascal BuggyBoard wheel:
- Remove the board from the stroller.
- Turn the board upside down on a soft surface.
- Find the wheel’s axle, retaining clip, or release tab.
- Release the retainer with your fingers or a small flat-head screwdriver.
- Slide the wheel or wheel assembly off the axle.
- Keep all clips, washers, and spacers in order.
- Install the replacement wheel in the same direction.
Many Lascal boards use a complete wheel assembly rather than a wheel that is meant to be split apart. If the wheel does not slide off after the locking part is released, replace the full assembly or contact Lascal support instead of prying into the frame.
Before you remove the wheel
Check the exact Lascal BuggyBoard model before starting. Look for a product label on the underside of the board or near the attachment arms. Common U.S. models include the BuggyBoard Mini, BuggyBoard Maxi, and BuggyBoard Maxi+.
You will usually need:
- A clean towel or soft mat
- A small flat-head screwdriver
- Needle-nose pliers, only if the axle has a metal retaining clip
- A small container for loose parts
- The replacement wheel or wheel assembly, if you have one
- The product manual, if available
Do not remove the wheel while the board is attached to a stroller. A loose board can shift, and the stroller may tip if you press against it.
Inspect the wheel before taking it apart
Look closely at the center of the wheel. You may see one of these systems:
- A release tab: Press the tab while pulling the wheel outward.
- A metal retaining clip: Remove the clip before sliding out the axle.
- A plastic axle end: The wheel may be part of a complete module.
- A fixed wheel assembly: The full fork or bracket may need to come off instead of the tire alone.
Take a quick photo before removal. This makes it easier to match the washer, spacer, clip, and wheel direction during reassembly.
How to remove a Lascal BuggyBoard wheel
The steps below cover the common removal process. Use the step that matches the hardware on your board.
1. Detach the BuggyBoard from the stroller
Release the BuggyBoard from its stroller connectors. Place the board upside down on a towel so the deck does not get scratched.
The board should rest flat. Do not place weight on the attachment arms, suspension parts, or plastic wheel mounts.
2. Clean the wheel mount
Brush away sand, hair, and dried mud around the wheel center. Dirt can hide the release tab and make the axle look stuck.
A dry brush works well. If the area is greasy, use a slightly damp cloth and let it dry before continuing. Avoid spraying lubricant or cleaner into the wheel housing.
3. Find the locking point
Look at the inside and outside of the wheel hub. The locking point may be located:
- In the center of the wheel
- Behind the wheel fork
- At the end of the axle
- On the side of the wheel module
Use a flashlight if needed. You are looking for the part that prevents the axle from sliding out.
4. Release the tab or retainer
If your BuggyBoard has a release tab, press it while pulling the wheel straight out. Use steady pressure rather than a sharp jerk.
If you see a metal clip, use needle-nose pliers to remove it. Hold your hand over the clip as you pull it away. Small clips can spring loose and are easy to lose.
If a small flat-head screwdriver is needed, use it only to lift the retainer. Do not use the screwdriver as a lever against the plastic wheel mount.
5. Slide out the axle or wheel assembly
Once the retainer is free, pull the wheel straight from the mount. Some versions allow the wheel to slide off the axle. Others require the entire wheel bracket or wheel module to come out.
Keep the parts in removal order. A typical arrangement may include:
- Wheel
- Spacer
- Washer
- Axle
- Retaining clip
The exact order depends on the BuggyBoard version. Do not assume that two wheels use identical parts if the board has been repaired before.
6. Compare the old and replacement parts
Place the new wheel beside the old one. Check that:
- The diameter is the same
- The axle hole matches
- The wheel turns in the same direction
- The hub shape matches
- The retaining groove is in the same location
- The replacement is listed for your exact BuggyBoard model
A wheel that looks close but does not fit correctly can wobble or come loose during use.
7. Reinstall the wheel
Slide the wheel or wheel assembly into the mount. Refit the washer, spacer, axle, and retaining clip in the same order used during removal.
Push the retainer fully into its groove. The wheel should sit straight and turn freely without rubbing the board frame.
Do not add extra washers or omit a spacer. These parts control the wheel position and help prevent side-to-side movement.
How to tell whether the wheel is installed correctly
A correctly installed Lascal BuggyBoard wheel should:
- Turn smoothly by hand
- Sit straight in the fork or mount
- Have only slight side play
- Stay attached when pulled gently
- Clear the board and frame during rotation
- Remain secure when the board is moved over a hard floor
After installation, place the board on the floor and press down lightly with your hand. Roll it forward and backward. Listen for scraping, clicking, or a repeated wobble.
Then attach the board to the stroller and test it without a child on the stroller. Walk slowly over a clean, flat surface. Check the wheel again before normal use.
What to do if the wheel will not come off
A stuck wheel is often caused by dirt, a bent axle, or a retainer that has not been fully released. Work through these checks in order.
The wheel does not move
Clean the hub and axle area. Then press the release tab again while pulling the wheel straight out.
If the axle is bent, do not force it through the mount. A bent axle can damage the plastic housing.
The wheel turns but will not slide off
The wheel may still be held by a clip on the opposite side. Inspect both sides of the hub before pulling harder.
Some BuggyBoard versions use a wheel assembly that must be released from the frame. In that case, trying to remove only the tire may damage the assembly.
The clip is missing
Do not use the board without the correct retaining clip. A missing clip can allow the wheel or axle to come out while the board is moving.
Order the correct replacement part for the model. A generic hardware clip may have the wrong size, shape, or strength.
The plastic mount is cracked
Stop using the BuggyBoard until the mount is repaired or replaced. A cracked wheel mount can fail under load, especially when the board crosses a curb or uneven sidewalk.
Do not repair a structural plastic part with glue alone. Contact Lascal or a qualified stroller repair service for the correct replacement option.
The replacement wheel is loose
Check the axle, spacer, and washer. A missing spacer can leave too much room for side-to-side movement.
If all parts are present, the wheel may not be compatible with your model. Match the part number and model name rather than relying only on wheel size.
Can you remove only the tire?
Usually, you should replace the wheel or wheel module rather than remove the rubber tire from the hub.
Some stroller wheels have a separate tire that can be pulled from the rim. The BuggyBoard wheel system may not be designed for this type of repair. Forcing the tire off can bend the rim, damage the hub, or create an uneven wheel.
If the replacement part is sold as a complete wheel, install the complete wheel. If Lascal supplies a tire-only part for your model, follow that model’s instructions.
When should you replace the wheel?
Replace the wheel when it has a flat spot, deep crack, severe wobble, or damaged hub. Also replace it if the wheel makes a grinding sound after cleaning.
Normal dirt can often be removed with a dry brush. Hair wrapped around the axle may also cause resistance. A wheel that remains rough or loose after cleaning may have a worn bearing, bent axle, or damaged mount.
Do not judge the wheel only by appearance. A wheel can look acceptable but still have a loose retainer or damaged axle.
Maintenance after wheel removal
Keep the wheel area clean and dry. After walks on wet sidewalks or dirty paths in the U.S., wipe away moisture and grit before storage.
Avoid heavy oil or grease unless the Lascal instructions specifically call for it. Lubricant can attract sand and dust, which may increase wear.
Check the wheels before each use if the board has been stored for a long time. Confirm that both wheels turn freely and that the attachment points remain secure.
Common mistakes to avoid
- Removing the wheel while the board is attached to the stroller
- Pulling before releasing the axle clip or tab
- Using a hammer to force the axle out
- Prying against the plastic frame
- Losing the washer or spacer
- Installing a wheel for a different BuggyBoard model
- Using the board with a missing retaining clip
- Testing the board with a child before checking the repair
- Applying excess lubricant to a dirty wheel
- Continuing to use a cracked wheel mount
The most serious mistake is treating every Lascal BuggyBoard model as identical. The removal method can change with the design and replacement part.
Frequently asked questions
Do I need special tools to remove Lascal BuggyBoard wheels?
Usually, no special tool is needed. You may need a small flat-head screwdriver to release a retainer and needle-nose pliers for a metal clip. Use tools only on the retaining hardware, not as a lever against the plastic frame.
Why is my Lascal BuggyBoard wheel wobbling?
A loose wheel may have a missing spacer, worn axle, damaged hub, loose retaining clip, or an incorrect replacement part. Remove the wheel and compare every part with the model instructions. Replace damaged hardware before using the board.
Can I remove the wheels without removing the BuggyBoard from the stroller?
You should remove the BuggyBoard first. This gives you better control and prevents pressure on the stroller connectors. It also reduces the risk of the stroller moving while you work.
Are BuggyBoard Mini and Maxi wheels interchangeable?
Do not assume they are interchangeable. Wheel size, axle shape, mounting parts, and wheel modules may differ. Use a replacement listed for the exact model and version.
What should I do if I cannot identify the model?
Look for the model name or product label on the underside of the board. Take clear photos of the deck, wheels, attachment arms, and wheel hardware. Send those details to Lascal support or a stroller repair professional before ordering parts.
Final check before use
After removing or replacing a Lascal BuggyBoard wheel, confirm that the wheel turns smoothly, the retainer is fully seated, and the wheel has no dangerous side-to-side movement. Test the board on a flat surface without a child first.
If the wheel, axle, or plastic mount remains damaged, do not use the board. Find the correct Lascal replacement part or seek help from the manufacturer or a qualified repair service.
