Removing Lascal BuggyBoard connectors is usually simple: first detach the BuggyBoard from the connectors, then release the straps or clamps that hold each connector to the stroller frame. Work with the stroller empty, apply the brake, and never force a button, buckle, or strap.
This guide is for parents and caregivers using Lascal BuggyBoard products in the United States. Connector shapes can vary by BuggyBoard model and production year, so check the manual for your exact model before using tools or removing a part that does not release by hand.
Introduction
A Lascal BuggyBoard normally uses two universal connectors. The connectors stay on the stroller frame, while the board can often be removed when you fold, store, or transport the stroller.
People often mean one of two things when they ask how to remove Lascal BuggyBoard connectors:
- Remove the board from the connectors.
- Remove the connectors from the stroller frame.
The first task uses the board-release buttons or tabs. The second task requires loosening the connector straps or clamps. The steps below cover both.
What You Need Before You Start
You usually need no special tools. Prepare a clear space and gather:
- The empty stroller
- The BuggyBoard
- A clean, dry cloth
- A flashlight, if the connector is hard to see
- The model manual, if available
Do not remove the board while a child stands on it. Put the stroller on a flat surface, engage the stroller brake, and keep the board unloaded.
Avoid screwdrivers, knives, pliers, oil, and spray lubricant unless the Lascal instructions for your model specifically call for them. A tool can crack the plastic body or damage the release mechanism.
How to Remove the BuggyBoard From Its Connectors
Removing the board first gives you better access to the connectors and reduces strain on the stroller frame.
- Park the stroller on a flat surface. Engage the brake and remove bags or other items that could pull the stroller backward.
- Stand behind the stroller. Keep one hand near the board so it does not drop when it releases.
- Find the release buttons or tabs. There is normally one release point at each connector.
- Press the release points. Press both sides as evenly as possible. Some models allow one side to release at a time.
- Lift the board away from the stroller. Use a steady motion. Do not twist the board from side to side.
- Place the board on the floor. Check that both connector hooks, pins, or locking parts have fully released.
If one side stays attached, do not pull harder. Lower the board, reset it, and press the stuck release point again. Dirt or side pressure may keep the locking part engaged.
How to tell that the board is fully released
The board should lift away without a sharp snap or heavy resistance. The connector parts should remain attached to the stroller, and the board should not hang from one side.
If the board still feels locked, inspect both connector areas. A strap may be tight, or the board may be putting sideways pressure on one connector.
How to Remove the Lascal Connectors From the Stroller
Once the board is off, remove each connector separately. The connector normally wraps around a stroller tube with a strap, buckle, or locking clamp.
- Identify the strap or clamp. Look at how the connector circles the stroller frame.
- Open the buckle or locking tab. Use your fingers to lift or press the release point built into the connector.
- Reduce the strap tension. Pull the loose end back through the buckle or strap slot. Do not yank the strap away from the connector.
- Unwrap the strap from the stroller tube. Keep the connector body supported so it does not swing against the frame.
- Slide the connector off the frame. If the frame tube has a bend or joint nearby, move the connector toward the nearest open section rather than forcing it over the bend.
- Repeat on the other side. Remove both connectors before folding the stroller.
- Wipe the parts clean. Remove dust and grit with a dry or slightly damp cloth.
Some Lascal connectors use a release button, while others rely more on a strap buckle or locking hook. The correct action is the one shown in the instructions for your model. If the strap does not loosen after the buckle opens, look for a second locking tab rather than pulling harder.
What to Do If a Connector Will Not Release
A connector that will not come off often has tension on it. The safest fix is to remove that tension before trying the release again.
| Symptom | Likely cause | Safe next step |
|---|---|---|
| The board will not lift off | One release point is still locked | Support the board and press each release point again |
| The strap will not slide | The strap is under load | Hold the connector body and push the strap toward the buckle before pulling it back |
| One connector is tight | The stroller frame is pressing against it | Move the connector slightly along the tube, then release it |
| The button feels stuck | Dirt or grit is in the opening | Wipe around the button and press it several times gently |
| The plastic flexes or cracks | Excess force or a damaged part | Stop and replace the connector or ask Lascal for support |
| The connector comes off but the strap stays caught | The strap is threaded through a locking slot | Open the buckle fully and retrace the strap path |
Do not pry under the connector with a metal tool. The connector may look simple, but a broken locking tab can prevent the board from attaching securely later.
If the connector remains stuck after cleaning and releasing the tension, take a clear photo of the part and compare it with the manual for your exact BuggyBoard model. Lascal support or an authorized retailer can help identify the correct release method and replacement part.
How to Reinstall the Connectors
Reinstall the connectors only when the stroller frame is clean and the connector parts are undamaged.
- Place each connector on the correct frame tube. Use the same left and right positions if the parts are marked.
- Keep each connector level. Both connectors should sit at similar heights.
- Route the strap as shown in the manual. A strap that skips a slot may loosen during use.
- Tighten the strap by hand. It should hold the connector firmly without crushing or deforming the stroller tube.
- Attach the BuggyBoard. Engage both sides until the locking parts are fully seated.
- Perform a hand check. Pull the board gently in several directions.
- Check clearance. Make sure the board does not rub against the stroller wheels, brake parts, folding joint, or frame.
The board should sit straight behind the stroller. If one side is higher, loosen and reposition the connector rather than correcting the angle by bending the board.
Basic safety check before use
Before a child steps on the board, confirm that:
- Both connectors are tight.
- Both sides of the board are locked.
- No strap hangs near a wheel.
- The board does not touch the brake or folding parts.
- The stroller remains stable when the board is unloaded.
- The BuggyBoard instructions allow use with your stroller model.
A hand tug is useful, but it is not a substitute for following the Lascal weight, age, and compatibility instructions.
Common Mistakes to Avoid
Pulling the board without pressing the releases
This can bend the connector hooks or place uneven force on the stroller frame. Always release the locking points first.
Cutting the connector straps
Cutting may seem faster, but it can make the connector unusable and may leave sharp strap ends. Loosen the buckle or locking slot instead.
Removing only one connector
A single connector can still hold the board in place. Remove both sides before storing the stroller or folding it.
Using oil or silicone spray
Lubricant may attract grit and can reach parts that need friction to stay locked. Clean the area with a cloth unless the model manual gives different care instructions.
Folding the stroller with the connectors attached
Some strollers may fold with the connectors in place, but the connectors can interfere with the fold or press against the frame. Remove them when the stroller manual or Lascal instructions require it.
Mixing connector parts from different kits
A replacement connector may look similar but use a different strap or locking shape. Use parts approved for the specific BuggyBoard and stroller combination.
When You Should Replace the Connectors
Replace a connector if you see:
- A crack in the plastic
- A broken release button
- A strap that will not lock
- A missing hook, pin, or buckle
- Severe wear that lets the connector move on the frame
- A connector that releases without pressing its release mechanism
Do not repair a cracked connector with glue. Glue may hide the damage but does not restore the locking strength needed to hold the board.
If you are unsure which replacement part you need, record the BuggyBoard model name, inspect any model label, and contact Lascal or the retailer that sold the product. Include photos of both connectors and the stroller attachment area.
Frequently Asked Questions
Can I leave the Lascal connectors on the stroller?
Often, yes, if the connectors do not block the stroller fold or interfere with wheels, brakes, or other moving parts. Check both the stroller instructions and the BuggyBoard instructions before leaving them attached.
Can I remove the BuggyBoard without removing the connectors?
Usually, yes. The board is commonly designed to detach from the connectors while the connectors remain on the stroller. Press the board-release points and lift the board away.
Do I need a screwdriver to remove the connectors?
Usually, no. The connector straps and release parts are generally operated by hand. Do not use a screwdriver unless the exact Lascal instructions for your model require it.
Why does one side release before the other?
Uneven frame pressure, strap tension, or a partly engaged locking hook can make one side release first. Support the board, reset both sides, and release them again without twisting the board.
What should I do if the connector broke during removal?
Stop using the BuggyBoard until the connector is replaced. A broken or loose connector can allow the board to detach or move into the stroller wheels.
Final Checklist
To remove Lascal BuggyBoard connectors safely:
- Empty the stroller and apply the brake.
- Release the board from both connectors.
- Open each connector buckle or locking tab.
- Feed the strap back through its slot.
- Unwrap the connector from the stroller frame.
- Inspect the parts for cracks, wear, or missing pieces.
- Store the connectors and board in a dry place.
If the release mechanism does not respond to gentle hand pressure, stop rather than forcing it. Confirm the BuggyBoard model and use the matching Lascal instructions or support service.
